Wingboarding

The kite repair kit by FixMyKite.com includes everything you need to do an emergency repair. This kit is essential for any kiteboard trip.

Ripstop sail tape is the best way to repair cuts in the sail of your kite. This "peel and stick" Nylon tape will provide the strength needed to repair small cuts in your kite to get you back out on the water fast.
*Can also be used on paragliders and sails.

Tef-Gel is a Corrsion inhibitor and Anti-Seize lubricant that is perfect for kiteboarding hardware, specifically for your Foils and Foil boards.

M6 Hydrofoil Mounting Screws

These are M6 Stainless Steel screws for any hydrofoil that uses the M6 T-nut, which which will work on all M6 Tracked hydrofoils.  These are Hex Head (socket cap), counter sink screws

Sold individually

This kit is an absolute no brainer to have in your bag. There is no excuse not to have this kit, because it has all the essentials in standard kite repair. Eliminate excuses and stay on the water with this fix kit.

The Fixmykite.com Travel Fix-Kit includes just about everything you need to fix your kite, lines, harness, board, and footstraps. All packaged neatly in a nice Dakine travel case so you are ready to go on your next kite adventure.

The Naish Surelock High Flow Inflate / Deflate Valve for 2020 and Newer Naish Kites and Wings.

Also Works on: 2021+ Crazyfly Kites,F-One, Flysurfer with SUP style valve.

New for 2020 is the full carbon, low profile FoilMount 3.0 Carbon.

This compressed carbon plate is not only beautiful it is also incredibly strong allowing it to be thinner than the original FoilMount.  This setup weighs just over 1lb so it is also about 30% lighter than previous models.  The new curved shape along with it's light weight and thinner profile make it incredibly low drag in the water.  You cannot tell there is a track mounted on the bottom of your board while using it without a hydrofoil.  We have also upgraded the included hardware.  Because this system is so thin we had to invent a new hardware set that would work with any base plate on the market call the Wizardhat Hardware.  Each FoilMount 3.0 Carbon includes a set of 4 Wizardhat hardware and they will allow you to attach any hydrofoil on the market to your FoilMount.

PKS Distribution again brings you the latest and greatest repair kit to keep you kiting longer. This Dacron patch kit includes 5 Dacron patches, alcohol prep pads and a 1oz tube of Seam grip repair adhesive that covers a multitude of repairs.

The FoilMount is a universal hydrofoil mounting system, this means that you can put a hydrofoil track on just about any board you already have.  

The FoilMount uses a specially designed 3M adhesive tape to stick to the bottom of your board.  It will accommodate any foil that uses the 90mm track system (this is industry standard).  It is a easy way to fix a broken track system.  It is also great for retrofitting boards with through bolt holes to give them the adjust-ability of a sliding track system.  The FoilMount can be removed but cannot be reused.  It is very easy to install, just prep the surface with alcohol, peel the tape backing, and stick!  Make sure you install the FoilMount on a flat surface on the board (no rocker, double or single concave).

Standard FoilMount
The standard mount is a flat plate that can be installed on any flat board surface.  It is suitable for most SUP boards, hydrofoil boards, Skim boards, Surfboards.  If you surface has some curve to it try the Ridge Mount system.  If you're trying to outfit a board with a tuttle box system or a windsurfing rig try the Hole Mount system.

The FoilMount is a universal hydrofoil mounting system, this means that you can put a hydrofoil track on just about any board you already have. Just Stick and Ride!

The FoilMount uses a specially designed 3M adhesive to stick to the bottom of your board. It will accommodate any foil that uses the 90mm track system (this is industry standard). It is an easy way to fix a broken track system on a production board. It is also great for retrofitting boards with through-bolt holes to give them the adjust-ability of a sliding track system.

The FoilMount is very easy to install; just clean the surface, prep the surface with alcohol, peel the backing on the adhesive, and finally stick onto the desired location.  Always dry-fit your mounting location before install because once it is stuck it is down for good.  

The FoilMount needs to be mounted on a flat surface with no concave or tail rocker.  It can be removed but cannot be reused.  

 

Ridge Mount FoilMount

This is the standard mount with a relief cut down the middle allowing for a mount on top of a ridge on the bottom of the board. The surface still needs to fairly flat, but allows for a slight ridge where the FoilMount will be installed.  It is suitable for most SUP boards, hydrofoil boards, Skim boards, Surfboards.

The 2.0 Standard now includes:

• Upgraded FoilMount plate with one piece adhesive backing
• 4 high strength brass or stainless steel slider nuts
• 1 set of 4 flat head M8x16mm bolts for Slingshot, Liquid Force, Cabrinha, and most other hydrofoils.
• 1 set of 4 flat head M6x12mm bolts for Takuma Surf hydrofoils
• 1 set of 4 pan head M8x20mm bolts for Moses and older Liquid Force foils (instructions, alcohol pads, scotch-brite pad, FoilMount plate)

The Duotone/North Airport Inflate/Deflate Valve will replace the inflate/deflate on all North 2014-2018 models except the 2014 Vegas and all 2019 Duotone kites.This blue cap valve is also a replacement for the North Yellow cap Inflate/deflate valve.  Made with TearAid to work with any bladder.

From the leader in repair technology, FixMyKite.com's Self-Stick-Valves will stick on any bladder material or color.  Simply peel and stick to make a fast and easy repair, or attach to a newly replaced bladder.  The specially formulated adhesive is incredibly durable making for a permanent repair.  Everything needed for installing the new valve is included in the package:  alcohol wipe and detailed instructions.

Wizardhat Hardware Set

This is the Wizardhat hardware only set.  If you just need some extra hardware

This hardware set will work with any base plate or 4-bolt tracked board on the market.  This included M8 or M6 base plates and tracks.  There is no more need for T-nuts or different sized bolts the Wizardhat will work on any.  Also, the way the bolt sticks up through the track on top makes it easy to line up with the base plate.

The Wizardhat hardware only set comes with 4 qty Wizardhat hardware (includes cone nut, t-bolt, and t-slider with a decal.   

*Be careful not to overtighten with the wrench as you will have a lot more leverage than the screwdrivers you have been using.

NORTH HYPERFLOW INFLATE VALVE works on new North kites starting in 2020 and beyond. Valves also work on Slingshot, Cabrinha, and Eleveight kites. Made with Tear-Aid to work with any bladder

How to install a fixmykite.com self stick valve?

1. Valve Removal: If replacing valve, carefully peel off old valve. If old valve does peel off, cut around circumference of valve to remove
2. Cleaning: Wipe area where valve will be placed with provided alcohol swab. DRY COMPLETELY WITH A CLEAN PAPER TOWEL.
3. Peel and Stick: Lay bladder out flat. If possible, have a friend lightly hold bladder on table or other smooth even surface. Peel off paper backing, center valve over hole, and place valve on bladder.
4. Press: Press valve from center outward to remove air bubbles and ensure proper adhesion and creases.

*Pro Tip- Use a hair dryer to heat the valve. This makes it easier to remove the valve. After placement of the Fixmykite self stick valve use the hair dryer again to warm the adhesive. Press the valve from the center out massaging and stretching creating positive adhesion. Be careful not to overheat the bladder or new valve.

If you’re unsure which value is required for your replacement project, please do not hesitate to contact us. Email:  [email protected] or Call 361-883-1473


Add Velcro Option
The "Add Velcro" option provides you with attached Velcro at the base of the valve just as you would see with the original factory bladder.  This part of the valve goes on the inside of the kite casing; the Velcro prevents the bladder from twisting when tightening the screw-cap. 

MEGA Option: The MEGA valve option refers to the size of the TEAR-AID PATCH ONLY.  MEGA patches are 4 inches in diameter as opposed to the standard valve patch which has a 3” diameter. This extra inch means 77% more adhesive base and surface area compared to the standard valve patch size. The MEGA-valve patch is necessary when the old valve is cut from the bladder or leaves a tear during removal. The additional surface area provided by the Mega valve Tear-Aid patch allows quick and easy bladder repair eliminating the need for an additional bladder patch. The Mega Valve Patch can also be used if the valve area of the bladder is warped.

If your old valve(s) cleanly peel(s) off, a larger Mega patch in most cases isn’t necessary.

Add Bladder Patch Install Kit Option
The Bladder Patch Install Kit is for use when your old valve has to be cut out of the bladder leaving a hole larger than the valve. If your old valve peels off of your bladder easily, you do NOT need the bladder patch kit. The Bladder Patch Install Kit includes a baggie of talcum powder and a 6x6-Inch (15.24 x 15.24cm) adhesive patch.

PKS M6 Studs for mounting Hydrofoil on deck with inserts.

Works with M6 Inserts and m6 hardware like the Wizard Hat Cone nuts.

Includes a set of 4 M6 Studs
  

*Be careful not to overtighten with the wrench as you will have a lot more leverage than the screwdrivers you have been using.

Wizardhat Hardware Set

This is the Wizardhat hardware only set.  If you just need some extra hardware

This hardware set will work with any base plate or 4-bolt tracked board on the market.  This included M8 or M6 base plates and tracks.  There is no more need for T-nuts or different sized bolts the Wizardhat will work on any.  Also, the way the bolt sticks up through the track on top makes it easy to line up with the base plate.

The Wizardhat hardware only set comes with 4 qty Wizardhat hardware (includes cone nut, t-bolt, and t-slider with a decal.   

*Be careful not to overtighten with the wrench as you will have a lot more leverage than the screwdrivers you have been using.

Wizardhat Cone Nut Set with m6x25mm Studs

This is the Wizardhat Cone Nuts with m6 x 25mm Studs.  If you just need some extra hardware.

Includes a set of 4 Cone Nuts with m6 x 25mm Studs

PKS M6 Studs with M6 Flanged nuts for mounting Hydrofoil on deck with inserts.

Includes a set of 4 M6 Studs and Flanged Nuts
  

*Be careful not to overtighten with the wrench as you will have a lot more leverage than the screwdrivers you have been using.

M8 Hydrofoil Track Stainless Steel T-Nuts

These are low profile replacement M8 Stainless Steel T-nuts for the any hydrofoil that uses the M8 T-nut, which just about all Tracked hydrofoils.  These are low profile meaning they are thinner than stock brass T-nuts by about 2.2mm from top to bottom but STRONGER.

Sold individually

M6 Hydrofoil Track Stainless Steel T-Nuts

These are Replacement M6 Stainless Steel T-nuts for the any hydrofoil that uses the M6 T-nut including Takuma, Naish and others  These are hard to get replacements that we now have in stock.  They are sold individually,  so if you need a set of 4 make sure to buy 4 of them.  Watch the video below for our testing of the M8 version against the brass version.

Here are the total dimensions of this part:

Track width: 8.5mm
Total width: 14.9mm
Total length: 23.9mm
Total height: 6.20mm

M8 Hydrofoil Track Brass T-Nuts

Extra brass T-nuts for your tracked hydrofoil.  These are salt water approved and perfect for all track systems.  They are M8 standard metric threads which is the convention for most hydrofoil tracks.

Sold Individually

The Ozone Big Boston Inflate/deflate kiteboarding Valve will replace the inflate/deflate on 2011 and newer Ozone Kite. This valve is also a compatable replacement for the Max Flow Valve from Liquid Force Kite (2011 and later) and All Switch kites. 

M8 Hydrofoil Mounting Screws

These are M8 Stainless Steel screws for any hydrofoil that uses the M8 T-nut, which just about all Tracked hydrofoils.  These are Hex Head(socket cap), counter sink screws

Sold individually

The FixMyKite.com Slingshot Complete Screw Valve is the new inflate/deflate screw valve with a built-in pump adapter that connects straight to any standard pump. Slingshot has these on some 2015 and newer kites.

The FixMyKite.com Cabrinha Airlock 2 Screw Valve is the new inflate/deflate screw valve with a built-in pump adapter that connects straight to any standard pump. Cabrinha started using these on 2014 kites, so they work on any 2014 and newer Cabrinha. The CAP will NOT WORK in the old Airlock 1 valve base (Cabrinha Airlock with old-style cap, pre-2014), but WILL WORK in 2014 and newer Cabrinha Airlock 2 valves. Also works on cloud kites by board riding maui. Made with TearAid to work with any bladder.

KiteFix’s best Seller! This repair package contains all you need to make permanent repairs. Hand assembled in Canada with high quality products, KiteFix’s repair kit is a must to be added to your equipment. Includes: 1 Glufix tube (1 oz.), 2 self-adhesive dacron rolls (Black & White, 5’ each.), 7 Fiberfix tapes (4’ each), bladder ultra-adhesive patches (3’’x 7’’), 1 Peel2Fix valve repair system, 1 Talkine bottle (3 oz.), 1 Glufix applicator, 3 tie raps, 1 detailed user’s guide, 1 pair of scissors, 1 plastic bag, 1 kitefix sticker. All put together in an airtight plastic container. (product code: kx-0401)

The mini-kit is our compact and economical package. Includes: 1 Glufix tube (1 oz.), 2 self-adhesive dacron stripes (black & white, 12’’), 1 Fiberfix tape (4’), bladder ultra-adhesive patches (3’’x3 ½”), 1 Glufix applicator, 1 detailed user’s guide, 1 brush, 1 KiteFix sticker.

For ripstop tears from 1'' to 48''

Fiberfix is the reinforcement fiber to be used with Glufix. This self-adhesive fiber increases up to 10 times the resistance of a repair. In order to have a permanent, ultra-resistant, esthetic repair in a record time, you simply have to join the 2 parts of a tear together with the Fiberfix and add a layer of Glufix over it. 7 colors package.
Size: 4’ each
 

Stainless steel rings are 1" diameter and are useful replacements in many bar/line set-ups and Depower Replacment lines.
Stainless steel ensures long-life in water, and hardened steel means it can take heavy loads and last under great pressure. 1-Inch Diameter

• 1-Inch Outer Diameter
• 3/4- Inch Inner Diameter

Stainless steel rings are useful replacements in many bar/line set-ups and Depower Replacment lines.
Stainless steel ensures long-life in water, and hardened steel means it can take heavy loads and last under great pressure.

Ripstop sail tape is the best way to repair cuts in the sail of your kite. This Nylon tape will provide the strength needed to repair small cuts without creating a huge mess to undo later if you decide to get the repair done professionally.

The Bladder-Patch Install Kit which includes a bladder protection sheet and a 6x6-Inch (15.24 x 15.24cm) Patch. If your screw valve has to be cut out of the old bladder, then you need the Patch Install Kit.

Fixmykite.com again brings you the latest and great kit to keep you kiting longer. This Tear Aid patch kit includes 3 different sizes of pre cut and rounded Tear Aid patches that cover a multitude of repairs.

Fixmykite.com again brings you the latest and great kit to keep you kiting longer. This Tear Aid patch kit includes 3 different sizes of pre cut and rounded Tear Aid patches that cover a multitude of repairs.

Dacron Tape should be used to repair all cuts in the leading edge and stuts of a inflatable kite. The dacron tape will provide the strength needed to repair small cuts without creating a huge mess to undo later if you decide to get the repair done professionally.

2" Wide (Two-inch Wide) Dacron Tape should be used to repair all cuts in the leading edge and struts of an inflatable kite.  The dacron tape will provide the strength needed to repair small cuts without creating a huge mess to undo later if you decide to get the repair done professionally.

Dacron Tape should be used to repair all cuts in the leading edge and struts of an inflatable kite. The dacron tape will provide the strength needed to repair small cuts without creating a huge mess to undo later if you decide to get the repair done professionally.

Tear Aid Bladder patches are the BEST patch out there to seal leaks and small cuts in bladders.  The roll can be cut into any size desired for patching, whether your bladder problem is small pinholes or 2-foot long cuts. 30 ft. x 1.25-Inch or 3-Inch or 6-inch Rolls (60 patches).  Note that long cuts (more than 6 inches) or cuts next to the seam of bladder can be harder to ensure a good seal on.  Long cuts are rarely straight lines.

 

PKS Smart Wing Leash System

The PKS Smart Wing Leash System includes the PKS Smart Cuff, a wrist cuff with multiple "locking" features to ensure the leash is not inadvertantly pulled off your wrist. The Elite Universal leah line with locking Larks Head Loops and the PKS Quick Connect Pigtail for quick and easy connections to any wing.

PKS Smart Cuff Wrist Leash Cuff:
The PKS Smart Cuff is a purpose built Wrist cuff for wingboarding that has two different "locking" features. The first is the Flat Lock low profile "tounge" that keeps the velcro closure flat and even help to prevent anything getting under it and opening the wrist leash. The second is The Over Lock perpindicular velcro closure that closes across the main velcro strap to prevent the wrist cuff strap from inadvertantly being opened.

PKS - Elite Universal Wing Leash:
The PKS Wing Leash is made using heavy duty 3/16" Spectra hollow core line with high elasticity bungee line inside.  The ends have 7/64th spectra line that has been wrapped and sewn in place creating a locking larks head for the ultimate strength, security, and versatility. By using the 7/64" spectra line for the loops, you are able to easily connect to multiple wing or harness connection types sush as hand shake,  larks head,  or ring connections. This combination gives you strength, versatility and ease of use.

PKS Leash Quick Connect Pigtail With Stopper Ball:
Designed to be used with Wing leashes for a quick connect and removal from one wing to another. No need to have a leash for every wing, just easily move your leash from wing to wing using the Quick Connect pigtail with stopper ball.

PKS Smart Cuff Wrist Leash Cuff:

The PKS Smart Cuff is a purpose built Wrist cuff for wingboarding that has two different "locking" features. The first is a low profile "tounge" that keeps the velcro closure flat and even help to prevent anything getting under it and opening the wrist leash. The second is an over lock velcro closure that closes across the main velcro strap to prevent the wrist cuff strap from inadvertantly being opened.

Key Features:

• High Grade Hook and Loop
• Smart Cuff with Mutiple "locking" Features
• Flat Lock, Low profile lay flat tounge
• Over Lock perpindicular locking tab
• Reeninforced Leash Connection Point
• Extra Wide Closure Loop
• Comfortable Neoprene Wrist lining

PKS - Elite Universal Wing Leash

The PKS Wing Leash is made using heavy duty 3/16" Spectra hollow core line with high elasticity bungee line inside.  The ends have 7/64th spectra line that has been wrapped and sewn in place creating a locking larks head for the ultimate strength, security, and versatility. By using the 7/64" spectra line for the loops, you are able to easily connect to multiple wing or harness connection types sush as hand shake,  larks head,  or ring connections. This combination gives you strength, versatility and ease of use.

PKS - Quick Connect Pigtail w/Stopper Ball

Designed to be used with Wing leashes for a quick connect and removal from one wing to another. No need to have a leash for every wing, just easily move your leash from wing to wing using the Quick Connect pigtail with stopper ball.

The Quick Connect Pigtail set allows you to have a much larger stopper to ensure that the connection is sure to hold.

PKS Adjustable/Universal Wingboarding Harness line.

The PKS Adjustable Wingboarding Harness Line is adjustable for length and will attach to wings with handles as well as wings with a boom.

PKS Wingboarding Rigid Handle/Boom Harness Line Easy Connect

The PKS Wingboarding Harness Line Easy Connect Adapter is an adapter for attaching the Wingboard Harness Line to a boom or rigin Handle on your wing.

Sizes:

• Small - Up to 3.5" Circumference (most rigid handles)
• Large - Up to 4" Circumference (Larger Booms)

Includes 1 Harness Line Easy Connect

PKS Wingboarding Harness Line Pigtail Adapter

The PKS Wingboarding Harness Line Pigtail Adapter is an adapter for attaching the Wingboard Harness Line to the handles or knots on your wing.

PKS Adjustable/Universal Wingboarding Harness line.

The PKS Adjustable Wingboarding Harness line is adjustable for length and will attach to wings with handles as well as wings with a boom.

Ozone Wing Waist Strap and Wing Leash Line

Complete Ozone Waist Leash for Ozone WASP or any other wing.

Ozone WASP Wrist Strap (strap only, no leash line)

Replacement Wrist Strap for use with the Ozone WASP, does not include the leash line.

Dakine DLX Wing / Kite Compression Bag
The perfect bag for your wing or kite. No more putting your wing or kite away wet, with its unfolding mesh pocket. This bag also features a sand pouch for anchoring your wing or kite to the ground on light wind days.

Size:
60 x 25 x 30cm

Key Features:

• Replaces heavier stock kite bags reducing overall travel bag weight
• Shoulder carry strap for beach travel
• Lightweight nylon fabric
• Four compression webbing strap